FX Pro Twist Throttle | Electric Dirt Bikes & eBikes
Get more control out of every twist. The FX Pro Twist Throttle combines a CNC-machined aluminum body, a genuine Honeywell Hall effect sensor, and a short 50° rotation with adjustments that let you dial in when power starts and how the throttle returns. Whether you are picking through a technical trail or getting on the power out of a corner, those adjustments help you build a throttle feel that suits your bike and your riding.
The Pro stands out for its adjustable start point, three spring tension settings, and precision 440C stainless steel bearing. The bearing supports smooth rotation with minimal play, while six blue-tint Grade 5 titanium fasteners finish off a solid, carefully machined assembly. It is a practical upgrade for riders who want a more precise connection between their right hand and the controller.
Short Throw, Adjustable Response
The 50° rotation reaches full throttle with less wrist movement, shortening the throw by 15° compared with the FX Classic's 65° rotation. The Honeywell Hall sensor provides a linear 0.83V to 4.2V output, giving a compatible, properly calibrated controller a progressive throttle signal.
A set screw on top of the housing mechanically adjusts the throttle's starting position without disassembly. This lets you reduce the rotation before your controller responds, or leave a deliberate dead band if that is how you prefer to ride. Stock controllers can vary in how much throttle movement they require before delivering power, so this adjustment gives you a way to fine-tune that initial response.
For controllers with throttle calibration: FX recommends leaving the start-point set screw backed out and calibrating through the controller to preserve a wider range of throttle resolution.
Choose Your Return Feel
-
Light: The lightest return setting, suited to technical trails and frequent low-speed throttle adjustments.
-
Medium: Balanced resistance for everyday track and trail riding.
-
Firm: The strongest return resistance for riders who prefer a more deliberate twist and a firm snap-back.
Machined Aluminum Construction
The housing is CNC-milled from solid 6061-T6 aluminum billet, an alloy used in aerospace and motorsport components. FX lists a material tensile strength of 310 MPa, compared with its cited 40 MPa plastic reference, machining tolerances of ±0.1 mm, and an approximate weight of 85 g.
A 440C stainless steel bearing is pressed into the aluminum housing to support consistent, smooth movement. The six Ti-6Al-4V Grade 5 titanium screws feature a distinctive blue tint, with corrosion resistance and low weight. FX describes the fasteners as stronger than steel at 40% less weight.
Choose from Black, Silver, Bronze, Gold, or Purple. Each finish is anodized directly into the polished aluminum surface rather than applied as paint or a surface coating.
Technical Specifications
-
Body material: 6061-T6 billet aluminum
-
Manufacturing: CNC-milled
-
Listed machining tolerance: ±0.1 mm
-
Listed material tensile strength: 310 MPa
-
Approximate weight: 85 g
-
Sensor: Genuine Honeywell Hall effect
-
Output voltage: Linear 0.83V to 4.2V, with adjustable starting voltage
-
Rotation: 50°
-
Start point: Adjustable through a top-mounted set screw
-
Handlebar diameter: 7/8 inch, 22.2 mm
-
Wire lead: 120 cm, customizable; certain bike-specific versions use a shorter cable
-
Default connector: Surron-style, with bike-specific connector options
-
Fasteners: Six Ti-6Al-4V Grade 5 titanium screws with a blue-tint finish
-
Bearing: 440C stainless steel
-
Weather rating: IP65
-
Spring tension: Three adjustable settings
-
Anodized colors: Black, Silver, Bronze, Gold, Purple
-
Warranty: 1 year
-
Manufacturer-listed price: $184.95
Bike & Controller Fitment
Select the connector option that matches your bike and controller. Some applications require start-button changes, connector modification, wiring, or controller calibration even when a matching throttle connector is available. FX does not currently offer a connector solution for bikes outside its listed applications.
-
Surron Light Bee, Light Bee 2, Ultra Bee; Segway X160 and X260: Plug-and-play with the standard Surron connector. Ultra Bee and Light Bee 2 versions include a shorter cable.
-
Surron Light Bee or Ultra Bee with EBMX X-9000, Torp, Ventus, or other aftermarket controllers using a Surron connector: Calibrate the throttle in the controller's app before use. The Ultra Bee selection includes a shorter cable.
-
E Ride Pro S and SS 2.0: Standard Surron triangular connector. The stock throttle's start-button wires must be connected together, or a separate handlebar-mounted momentary button must be installed to replace the stock park button.
-
E Ride Pro SS 3.0 and SR: Standard Surron connector. Disable the start button through the E Ride Pro app, or install a separate handlebar-mounted momentary button to replace the stock throttle button.
-
Talaria MX3: Standard Surron connector. Connect the start-button wires together or install a separate handlebar-mounted momentary button to replace the park button.
-
Talaria MX4, MX5, and XXX: 5-pin circular green connector. The supplied FX cable automatically bypasses the start button. Trim the tubing on the controller-side connector until it sits flush with the green connector face for proper fit.
-
Y-Volt Surge V: Plug-and-play with a 5-pin green male circular connector.
-
Altis Sigma: Compatible with 2025 and 2026 models using the 3-pin rectangular white connector. The 8-pin white square connector version is not currently available.
-
Ventus 1+ with v1.7 throttle: Plug-and-play with a 3-pin white rectangular connector.
-
MACFOX bikes with a stock thumb throttle: Plug-and-play with a 3-pin male yellow or orange circular connector.
-
P-51 with stock controller: FX Pro only. Uses a 3-pin circular yellow or orange male connector.
-
RAWR Mantis Pro: Plug-and-play with an M7 small yellow 3-pin circular connector.
-
Falcon Pro and Falcon GT: FX Pro only; not compatible with the FX Classic. Uses a 5-pin green female circular connector. The supplied FX cable bypasses the start button.
-
79Bike Falcon Lite: FX Pro only; not compatible with the FX Classic. Uses a 3-pin male orange or yellow connector.
-
Bonnell 775MX: Plug-and-play with a 3-pin female yellow or orange circular connector.
-
Zooz Gen 1: Plug-and-play with a 3-pin male yellow or orange connector.
-
Zooz Gen 2, Gen 3, Gen 4, and Flex: Plug-and-play with a 3-pin male yellow or orange connector.
-
Throne Strike Shadow: Plug-and-play with a Surron-style male connector.
-
SRPNT Z27 and X8: Plug-and-play with a standard Surron female connector.
-
Tuttio Solei 01: Requires an adapter. With the appropriate adapter installed, the throttle connection is standard Surron. Consult FX's adapter information before ordering.
-
Juiced eBikes: Plug-and-play with a 3-pin male circular orange or yellow connector.
-
Arctic Leopard bikes: Plug-and-play with a 3-pin female white rectangular connector.
-
Yozma IN 10: Standard Surron male-side connector. Direct soldering at the handlebar is an alternative; follow FX's model-specific wire-color connection information.
-
BAC4000, BAC855, and BAC8000 controllers: Throttle calibration is required in the controller settings. No connector is supplied for these applications; wires must be joined or soldered.
-
Fardriver controllers: FX lists compatibility with all Fardriver controllers, with calibration required after installation. No connector is supplied; wires must be joined or soldered.
-
VESC-based controllers: Use the FX Pro's 0.83V to 4.2V range and perform auto-calibration in VESC Tool. Supply and install a suitable connector or solder the wires. The FX Classic uses a different starting voltage of 0.87V.
FX Pro vs. FX Classic
The Pro adds a 50° rotation and an adjustable start-point set screw, compared with the Classic's 65° rotation and fixed start point. Both models use Grade 5 titanium fasteners, a 440C stainless steel bearing, and five anodized color options. The Pro features six blue-tint titanium screws and supports the Pro-only fitments listed above.
Included in the Box
- FX Pro Twist Throttle in your selected color
- Pre-wired connector, with Surron-style as the default
- Six Grade 5 titanium screws with a burnt blue-tint finish
- Pre-installed start-point set screw
- 3 mm, 2 mm, and 1.5 mm hex keys
- FX stickers
- Installation instructions
Who Is the FX Pro For?
-
Technical trail riders: Riders who want adjustable return tension and a carefully tuned starting point for low-speed power delivery.
-
Track riders: Riders who prefer a short 50° throw and firmer spring resistance when moving quickly between throttle positions.
-
Riders refining a stock or upgraded bike: Owners looking for a machined aluminum throttle with bearing-supported movement and adjustment options to suit their controller.